MOON Nēo Mono Power Amplifier - 400M
Extremely powerful, yet with a delicacy and articulation of the best amplifiers out there, the Nēo 400M can take on virtually any loudspeaker you connect it to. Delivering a bottom-end slam, with authority and weight to the foundation of the music, it will transport you into a live concert environment. On the top end of the musical spectrum, the Nēo 400M delivers finesse, detail and refinement that can challenge your perception of reality vs. recorded music.
When used in conjunction with the Nēo 350P Preamplifier, the results are without equal. There isn't a more refined combination at this price point. An ultimate combination for the discerning music lover, and for those who like to listen at higher sound levels.
Of course, key features you'd expect in a MOON Nēo Series product are present such as 12V triggers and an RS-232 port for custom-install environments. Finally, the Nēo 400M is available in three different finishes: the standard "all black", as well as special order "all silver" or "2-tone" (black & silver)
Nēo 400M Technical Features
· A "no overall feedback" design resulting in genuine real-time amplification, a more accurate
musical reproduction with respect to tonality, virtually non-existent intermodulation distortion
and the elimination of common phase errors resulting from feedback
· An oversized power supply
· Custom proprietary toroidal transformer design with lower magnetic, electrical and thermal loss,
yielding an improved power transfer and lower regulation factor. The result is increased current speed
and better dynamics
· Precision matched proprietary MOON Bipolar output transistors with unprecedented gain linearity,
resulting in improved bass response and even more accurate sonic reproduction
· A high damping factor for superior musical dynamics, improved signal speed and refined timbre accuracy
· Fully balanced differential circuitry
· "Class A" output to 10 watts for greater efficiency
· 12 Volt trigger input/output for remote operations
· RS-232 port for (i) full unsolicited bidirectional feedback and (ii) firmware updates
· Rigid chassis construction to minimize the effects of external vibrations
· Optimized selection of very high quality electronic components
· Low operating temperature for an ultra-long life expectancy.
| Nēo 400M Detailed Specifications | |
| Type | Solid State |
| Configuration | Mono - Differential |
| Power Supply Transformers | 400VA |
| Power Supply Capacitance | 85,000µF |
| Class Of Operation | A/AB |
| Balanced Inputs | XLR - 1 |
| Single-ended Inputs | RCA - 1 |
| Input Device Type | J-FETs |
| Input Impedance | 47.5KΩ |
| Input Sensitivity | 800mV RMS |
| Output Device Type | Bipolars - 8 |
| Output Binding Posts | 1 pair - 5-way, Gold-plated, Shielded |
| Output Power @ 8Ω | 400 Watts |
| Output Power @ 4Ω | 650 Watts |
| Frequency Response | 10Hz - 125kHz (+0/-3dB) |
| Output Impedance | < 0.01Ω |
| Damping Factor (static) | > 800 |
| Gain | 36dB |
| Signal-to-noise Ratio | 106dB @ full power |
| Maximum Output Voltage | 60 Volts |
| Slew Rate | 60 V/µs |
| Maximum Current - Peak | 56 amperes |
| Maximum Current - Continuous | 26 amperes |
| IMD | Unmeasureable |
| THD (20Hz - 20kHz @ 1 watt) | 0.02% |
| THD (20Hz - 20kHz @ 400 watts) | 0.05% |
| 12 Volt Trigger Input/Output Operation | Direct Logic (0V = off, 12V=on) using a 3.5mm mono jack with an output impedance of 1000Ω and current requirement of 12mA |
| RS-232 Port | 9-pin female DB connector |
| Power Consumption @ idle | 36 Watts |
| AC Power Requirements | 120V / 60Hz 220-240V / 50Hz |
| Fuse Replacement 120V / 220-240V | 8.0A long fast blow / 4.0 long fast blow |
| Shipping weight | 34 lbs / 15 kgs |
| Dimensions (W x H x D) | 16.9 x 3.5 x 14.0 in. (42.9 x 8.9 x 35.6 cm.) |
| Specifications are subject to change without notice. |
Write a review
Your Name:Your Review: Note: HTML is not translated!
Rating: Bad Good
Enter the code in the box below: